Order service now
icon-address zhengzhou , china

welcome to visit us

Contact Us

[email protected]

High and New Industrial Zone, Kexue Revenue, High and New Technology Industrial Development Zone, Zhengzhou, China

Get Latest Price
Get in Touch

If you have any problems about our product and service,please feel free to give your inquiry in the form below. We will reply you within 24 hours as soon as possible.Thank you!

  • Standard Test Methods for Cold Crushing Strength and

    Standard Test Methods for Cold Crushing Strength and

    3.3 Considerable care must be used to compare the results of different determinations of the cold crushing strength or modulus of rupture. The specimen size and shape, the nature of the specimen faces (that is, as-formed, sawed, or ground), the orientation of those faces during testing, the loading geometry, and the rate of load application may all significantly affect the numerical results ...

    More Details
  • Standard Test Method for Cold Bonding Strength of

    Standard Test Method for Cold Bonding Strength of

    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.. ASTM Standards. C78/C78M Test Method for Flexural Strength of Concrete (Using Simple Beam with Third-Point Loading). C133 Test Methods for Cold Crushing Strength and Modulus of Rupture of Refractories

    More Details
  • Table 1 Setting Time of Concrete at Various Temperature

    Table 1 Setting Time of Concrete at Various Temperature

    However, proper cold weather concrete curing will enhance concrete strength development. Hot weather is defined as any combination is high ambient temperature, high concrete temperature, low relative humidity, and wind velocity. Cold weather period, as defined by ACI Committee 306, is when one of the following conditions occur for three ...

    More Details
  • On a qualitative relationship between degree of

    On a qualitative relationship between degree of

    May 01, 2003 The heating rate was 4 K/min. 3.2. Measurement of cold crushing strength (CCS) The measurement of CCS was carried out with five cylindrical samples 50 mm in diameter and 50 mm in height. The specimens were subjected to direct compression between two steel platens in a load-controlled testing machine in accordance with preliminary standard ENV 1402.

    More Details
  • Compressive Strength of Concrete and Concrete Testing

    Compressive Strength of Concrete and Concrete Testing

    Gradually increase the load until it fails. The rate of loading is 0.6 0.2 N/mm 2 /s; Record the maximum force from the machine; The same procedure is followed in the testing of concrete cylinders also. Compressive strength can be calculated from the following equation. Compressive Strength = Applied Maximum Load / Top surface area of the ...

    More Details
  • How to Calculate Rate of Loading for Concrete Cube Testing

    How to Calculate Rate of Loading for Concrete Cube Testing

    Sep 11, 2019 1.373 x 10 x 10 = 137.3 Kn. So rate of loading will be = 137.3 / 60 = 2.88 Kn/Sec. Same way you can calculate rate of loading for each cube size you test at your laboratory. Kindly note above calculation are done considering your cube testing machine applies load in Kn, if your machine applies load in Kg or Mt kindly change the load on cube ...

    More Details
  • 602 Concrete Pavement Construction MediaWiki

    602 Concrete Pavement Construction MediaWiki

    Sep 18, 2019 File:CMU 602 Load Tranfer Assembly Inspections Presentation.pdf. After the base is properly compacted and fine trimmed to receive the concrete, load transfer assemblies are placed at joint locations. The inspector should work closely with the …

    More Details
  • IS 516 1959 Method of Tests for Strength of Concrete

    IS 516 1959 Method of Tests for Strength of Concrete

    IS:516-1959 Indian Standard METHODS OF TESTS FOR STRENGTH OF CONCRETE o. FOREWORD 0.1 This Indian Standard was adopted by the Indian Standards Institution on 10 November 1959, after the draft finalized by the Cement and Concrete Sectional Committee had been approved by the Building Division Council. 0.2 Testing plays an important role in controlling the quality of cement ...

    More Details
  • Compressive Strength of Concrete Cube Test Procedure

    Compressive Strength of Concrete Cube Test Procedure

    May 18, 2018 Compressive strength of Concrete Formula: The Compressive strength of specimen can be calculated by dividing maximum load carried by the specimen by cross-sectional area of the specimen cubes. The surface area of specimen: = 150 x 150 = 22500mm = 225cm . Assume, The Max compression load is 450KN.

    More Details
  • Modulus of Rupture an overview ScienceDirect Topics

    Modulus of Rupture an overview ScienceDirect Topics

    Cold Crushing Strength (psi, kg/cm 2) Cold crushing strength (CCS) is a compressive test that measures the ability of a product to withstand a given load, normally measured at room temperature after firing to specific temperatures. It is measured by ASTM C133.

    More Details
  • Compressive Strength of Concrete Cube Test Procedure

    Compressive Strength of Concrete Cube Test Procedure

    Load should be applied gradually at the rate of 140 kg/cm2 per minute till the Specimens fails. Load at the failure divided by area of specimen gives the compressive strength of concrete. Following are the procedure for testing the Compressive strength of Concrete Cubes

    More Details
  • The 28 Day Myth National Precast Concrete Association

    The 28 Day Myth National Precast Concrete Association

    Oct 28, 2013 Specified concrete compressive strength is the minimum compressive strength at which the concrete should fail in standard tests of 28-day-old concrete cylinders. A typical concrete compressive strength specification requires 4,000 to 5,000 psi at 28 days.

    More Details

Hot news

Click avatar to contact us
Click avatar to contact us
gotop